Best Homelab Rack
Pick your rack standard before you pick a brand, because the two do not mix. If your homelab is mini PCs, a Raspberry Pi or two, a small 2.5-gigabit switch, and maybe a short NAS, buy a 10-inch mini rack like the DeskPi RackMate: it sits on a desk, stays quiet, and costs about $120. If you run full-size 19-inch gear, a rackmount NAS, a 1U UPS, a managed switch with mounting ears, then skip the mini rack entirely and get a 19-inch open-frame rack, which is the cheapest way to hold real equipment and has the best airflow. Everything else here is a variation on those two: a wall-mount cabinet when you only have networking gear, a used enclosed rack when you want doors and casters, and an IKEA Lack table when you want 19-inch mounting for the price of lunch.
Updated 2026-11-12 · by Jonathan Caruso
This page has affiliate links, so HomelabCompass may earn a commission at no cost to you. As an Amazon Associate, HomelabCompass earns from qualifying purchases. It never changes a verdict. How the site is funded
Top pick
10-inch mini rack (DeskPi / GeeekPi RackMate)
For the way most homelabs actually look in 2026, a stack of mini PCs and a small switch, the 10-inch mini rack is the right box. The DeskPi and GeeekPi RackMate line (T0 at 4U, T1 at 8U, T2 at 12U) is an open aluminum frame that sits on a desk or a shelf, weighs almost nothing, and runs about $100 to $160. The catch is the width: a 10-inch rack sets its mounting rails roughly 236 mm apart, not the 465 mm of a real 19-inch rack, so full-size gear will not fit. What does fit is mini PCs and Raspberry Pis on half-U cantilever shelves, a handful of native 10-inch switches, and 10-inch patch panels and PDUs. That matches the gear most people own, which is why the format took off. If everything you run is small and low-power, this is the cheapest, quietest, best-looking way to get it off the floor.
The options
10-inch mini rack (DeskPi / GeeekPi RackMate)
New, roughly $100 to $160 for the frameAn open desktop frame in the 10-inch standard: the RackMate T0 (4U), T1 (8U), and T2 (12U), with half-U shelves, patch panels, and PDUs sold to fit.
- Runs on
- 10-inch mounting width (rails about 236 mm apart), shallow depth of roughly 200 to 260 mm, aluminum open frame; holds mini PCs and Raspberry Pis on shelves, a few native 10-inch switches, and 10-inch patch panels and PDUs. Standard 19-inch gear does not fit.
- Pick it if
- Your homelab is mini PCs, a Pi or two, and a small switch, and you want it tidy on a desk without a fan wall. The default for a small 2026 setup.
19-inch open-frame 4-post rack
New, roughly $120 to $280 depending on heightA floor-standing steel frame in the real 19-inch standard with no doors or sides, in sizes like the StarTech 12U and 25U with adjustable mounting depth.
- Runs on
- Full 19-inch mounting width, adjustable depth (the StarTech 12U runs about 18 to 30 inches, the 25U about 22 to 40 inches), high static load in the hundreds of pounds, open on all sides for airflow; takes any rackmount server, NAS, UPS, or switch.
- Pick it if
- You run full-size 19-inch gear and want the cheapest way to mount it with the best cooling. The homelab workhorse once you outgrow a desk.
Wall-mount network cabinet
New, roughly $80 to $220An enclosed, lockable 19-inch box that bolts to a wall or stands on the floor, in 6U, 9U, and 12U sizes from NavePoint, Tripp Lite, and StarTech, often with a glass door and a fan.
- Runs on
- Full 19-inch width but shallow depth (often 12 to 24 inches), a lockable door, a lower weight rating than a floor rack (roughly 100 to 200 pounds); sized for a switch, a patch panel, a router, and a small UPS, not deep servers.
- Pick it if
- Your gear is mostly networking and you want it off the floor, out of reach, and behind a door in a closet or garage. Measure the depth first.
Enclosed 19-inch floor rack
New, roughly $500 to $1,500; a used enterprise rack, roughly $100 to $400 locallyA full enclosed rack with doors, side panels, and casters: a new StarTech or Tripp Lite SmartRack, or a used enterprise 42U like an APC NetShelter off the second-hand market.
- Runs on
- Full 19-inch width, full depth for the longest servers, perforated doors, cable management, casters, and heavy static capacity; the used route is the value play, but the rack weighs well over 100 pounds empty and needs two people and a truck.
- Pick it if
- You run full-depth rackmount servers, want doors and a tidy look, and have the floor space. A used enterprise rack is the cheapest path to a real one if you can move it.
DIY IKEA Lack rack (LackRack)
Roughly $10 to $20 per table, plus screws or bracketsAn IKEA Lack side table used as a rack: the inside distance between the legs is about 19 inches, so rackmount gear rests across the gap. Stack tables for more height.
- Runs on
- Fits 19-inch gear by coincidence of the table's inner width; no real mounting rails, so gear rests on the ledge or on added brackets; the legs are hollow particleboard and weak, so keep it to light switches, patch panels, and a Pi shelf, not heavy servers. About 8U per table.
- Pick it if
- You want 19-inch mounting for almost nothing and your gear is light. A genuine homelab classic, not a joke, as long as you respect the weight limit.
How to choose
Settle the 10-inch versus 19-inch question first, because it decides everything else and it is the mistake people make most. A 10-inch mini rack is lovely for mini PCs and a Pi, but the rails are too narrow for any standard rackmount NAS, UPS, or switch with ears, so if you own or plan to own full-size gear, a mini rack is a dead end you will replace in six months. Look at what you actually run. If it is a couple of mini PCs and a small switch, go 10-inch and enjoy the size. If there is a rackmount NAS, a 1U UPS, or a 24-port switch in the plan, go 19-inch from the start and save yourself the second purchase.
Then size it, and size up. Count the U your current gear needs, add room for a patch panel and a PDU, and buy more height than that; 9U to 15U is the sweet spot for most homelabs, and empty U fill faster than you expect. Depth is the quiet killer: a full-depth rackmount server can be 25 inches or more front to back, so a shallow wall-mount cabinet will not close its door on one, and even some open-frame racks need their rails set deep. Measure the equipment and the rack's adjustable depth before you buy. Open frames give the best airflow and the lowest price, and they let loud rack fans breathe; enclosed cabinets look tidier and lock, but they trap heat unless you add fans, and the stock 40 mm fans in cheap cabinets scream. If the rack lives near people, that noise is part of the decision.
Last, plan the boring parts, because they are where projects stall. A 19-inch rack with square holes needs cage nuts and rack screws, which almost never come in the box, so order a pack with the rack; servers want proper rails, while a plain shelf holds anything that lacks ears. Load heavy gear low so the rack does not get top-heavy, keep a UPS at the bottom, and leave a little slack in every cable run. None of this changes that a rack is a box to hold computers, not the computers, so spend the real money on what goes in it: pick the operating system for the server, and because rack gear tends to idle higher and run 24/7, put the yearly cost through the power calculator before you fill it.
The verdict
Buy the rack that fits your gear. If your homelab is mini PCs, a Raspberry Pi or two, and a small switch, a 10-inch mini rack like the DeskPi RackMate is the pick: desk-sized, quiet, about $120, and made for exactly that class of hardware. If you run full-size 19-inch equipment, skip the mini rack and get a 19-inch open-frame rack, which mounts anything and cools the best for the least money. Use a wall-mount cabinet when the gear is mostly networking and you want it locked in a closet, a used enclosed enterprise rack when you want doors and casters and can move the weight, and an IKEA Lack table when you want 19-inch mounting for the price of lunch and your gear is light. Size up on height, measure depth before you buy, and remember the rack is just the box: spend on what goes in it, like a solid mini PC or a rackmount NAS, pick its operating system, and price the 24/7 running cost in the power calculator first.
What to buy
What fits the advice above. Amazon links open a search, so you can compare current models and prices.
DeskPi RackMate (10-inch mini rack)
The pick for a mini-PC homelab: an open 10-inch desktop frame in 8U or 12U that holds mini PCs, a Pi, and a small switch on half-U shelves, for about $120.
See it on AmazonStarTech open-frame 4-post rack
The 19-inch workhorse: a floor-standing open frame with adjustable depth that mounts full-size gear and cools the best, from 12U up.
See it on AmazonNavePoint wall-mount cabinet
The networking pick: an enclosed, lockable 19-inch cabinet in 6U to 12U that bolts to a wall or sits on the floor, for a switch, a patch panel, and a small UPS. Check the depth.
See it on Amazon
FAQ
What is the best homelab rack?
For most homelabs in 2026, a 10-inch mini rack like the DeskPi RackMate: it holds the mini PCs, Pis, and small switch most people run, sits on a desk, and costs about $120. If you run full-size 19-inch gear such as a rackmount NAS, a UPS, or an enterprise switch, that mini rack will not fit any of it, so buy a 19-inch open-frame rack instead; it is the cheapest way to mount real equipment and cools the best. Match the rack to your gear, not the other way around.
How much does a homelab rack cost?
A 10-inch mini rack runs about $100 to $160. A 19-inch open-frame rack is roughly $120 to $280 depending on height. A wall-mount network cabinet is $80 to $220. A new enclosed floor rack is $500 to $1,500, while a used enterprise 42U off the local second-hand market can be $100 to $400 if you can haul it. The cheapest real 19-inch option is an IKEA Lack table at $10 to $20, which fits rackmount gear across its legs.
What is a 10-inch mini rack?
A smaller rack standard that keeps the 1U height of a full rack (1.75 inches per U) but sets the mounting rails about 236 mm apart instead of the 19-inch standard's 465 mm. The DeskPi and GeeekPi RackMate frames made it popular for homelabs. It fits mini PCs and Raspberry Pis on half-U shelves, a few native 10-inch switches, and 10-inch patch panels and PDUs. It does not fit standard 19-inch rackmount gear, so check your equipment before buying one.
Do I need a rack for a homelab?
No. Plenty of homelabs run fine as a mini PC and a NAS on a shelf. A rack earns its place when you have enough gear that stacking it gets messy or hot, when you want rackmount equipment mounted properly, or when you are consolidating into one spot. If you own two or three boxes and a switch, a shelf or a small mini rack is enough; the full 19-inch rack is for when the pile has outgrown the shelf.
How deep does a homelab rack need to be?
It depends on the deepest thing going in it. A full-depth rackmount server runs 25 to 28 inches front to back and needs a full-depth rack or an open frame with the rails set deep. Networking gear, a short NAS, and mini PCs on shelves fit shallow wall-mount cabinets under 20 inches. Measure your equipment, add a couple of inches for cable bends behind it, and check the rack's depth (adjustable on most open-frame racks) before you buy.
What is a server rack called?
A standard server rack is a 19-inch rack, named for the 19-inch mounting width defined by the EIA-310 standard; you will also hear relay rack or equipment rack. Height is measured in rack units, where 1U equals 1.75 inches, so a 12U rack holds twelve of those slots. The smaller homelab format is a 10-inch rack, or mini rack, which uses the same U height but a narrower rail spacing.
Can I build a DIY homelab rack?
Yes, and the classic is the IKEA Lack table, nicknamed the LackRack: the inside width between its legs is about 19 inches, so rackmount gear rests across the gap, and you can stack tables for more height. It costs $10 to $20 a table. The catch is that the legs are hollow particleboard, so it is fine for light switches, patch panels, and a Pi shelf but not for heavy servers; reinforce the legs or add real rails if you want to trust it with weight.
How do I mount equipment in a rack?
On a square-hole 19-inch rack, press cage nuts into the holes where you want each piece, line up the device's ears, and drive rack screws through into the cage nuts; buy a pack of both with the rack, since they rarely come included. Servers use sliding rails instead of ears, and gear without rack ears sits on a shelf. Mount heavy items like a UPS at the bottom so the rack stays stable, and work from the bottom up so you are not reaching over installed gear.